FrSky - RX8R PRO - EU LBT
Code: FrSky-01-01-RX8R-PRO-EU
An upgraded version based on the RX8R receiver, it has all the same features including redundancy. The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.
New PRO version 'An upgraded version based on the RX8R receiver, it has all the same features including redundancy. The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.'
Strong anti-interference performance in ignition process
Higher precision of PWM
Lower latency on the PWM output
Support redundancy function
Smart Port enabled and support telemetry data transmission
A multifunctional receiver from FrSky! RX8R, a receiver which has 8/16ch full duplex telemetry and redundancy functions!
Parallel two RX8R to become a 16 channel receiver
Smart Port enabled, realizing two-way full duplex transmission
Supports redundant transmission of two Tx modules in parallel (Sbus input: the signal from the slave receiver(Sbus receiver) for backup)
The redundancy function For the master and slave receivers, when the master receiver goes into failsafe, the output signal from the slave receiver will be used until the master receiver works again. Notes
When both the master and slave receivers go into failsafe, the failsafe signal from the master receiver will be output.
The slave receiver should be in no telemetry mode
Specification:
Dimension: 46.25×26.6×14.2mm (L×W×H)
Weight: 12.1g
Number of Channels: 16CH (1-8ch from conventional channel output, 1-16ch from SBUS port, or combine two RX8R to become a 16 channels receivers)
With RSSI Output on Board: Analog 0-3.3V
Operating Voltage Range: 4.0-10V
Operating Current: 100mA@5V
Operating Range: full range (>1.5km)
Firmware Upgradeable
Compatibility: FrSky radios/transmitter modules in D8/D16 mode
Please note this rx has the FrSky EU LBT firmware installed, which greatly improves RF performance, range and stability. This firmware is not compatible with the previous EU firmware. It is recommended that you upgrade your radios, modules and receivers from the old EU firmware to the corresponding EU LBT firmware. Use either FrSky radios or PC for upgrading. Please refer to the FrSky website download section for the firmware download.
Includes:
RX8R Receiver
Manual
FrSky Downloads for Latest Firmware, Manuals and Certificates Product Manual
Code: FrSky-01-01-RX8R-PRO-EU
An upgraded version based on the RX8R receiver, it has all the same features including redundancy. The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.
New PRO version 'An upgraded version based on the RX8R receiver, it has all the same features including redundancy. The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.'
Strong anti-interference performance in ignition process
Higher precision of PWM
Lower latency on the PWM output
Support redundancy function
Smart Port enabled and support telemetry data transmission
A multifunctional receiver from FrSky! RX8R, a receiver which has 8/16ch full duplex telemetry and redundancy functions!
Parallel two RX8R to become a 16 channel receiver
Smart Port enabled, realizing two-way full duplex transmission
Supports redundant transmission of two Tx modules in parallel (Sbus input: the signal from the slave receiver(Sbus receiver) for backup)
The redundancy function For the master and slave receivers, when the master receiver goes into failsafe, the output signal from the slave receiver will be used until the master receiver works again. Notes
When both the master and slave receivers go into failsafe, the failsafe signal from the master receiver will be output.
The slave receiver should be in no telemetry mode
Specification:
Dimension: 46.25×26.6×14.2mm (L×W×H)
Weight: 12.1g
Number of Channels: 16CH (1-8ch from conventional channel output, 1-16ch from SBUS port, or combine two RX8R to become a 16 channels receivers)
With RSSI Output on Board: Analog 0-3.3V
Operating Voltage Range: 4.0-10V
Operating Current: 100mA@5V
Operating Range: full range (>1.5km)
Firmware Upgradeable
Compatibility: FrSky radios/transmitter modules in D8/D16 mode
Please note this rx has the FrSky EU LBT firmware installed, which greatly improves RF performance, range and stability. This firmware is not compatible with the previous EU firmware. It is recommended that you upgrade your radios, modules and receivers from the old EU firmware to the corresponding EU LBT firmware. Use either FrSky radios or PC for upgrading. Please refer to the FrSky website download section for the firmware download.
Includes:
RX8R Receiver
Manual
FrSky Downloads for Latest Firmware, Manuals and Certificates Product Manual
Code: FrSky-01-01-RX8R-PRO-EU
An upgraded version based on the RX8R receiver, it has all the same features including redundancy. The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.
New PRO version 'An upgraded version based on the RX8R receiver, it has all the same features including redundancy. The Pro version has higher precision and lower latency. It’s deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high speed mode. A feature that deserves mention is the decreased effect of interference caused by the ignition process.'
Strong anti-interference performance in ignition process
Higher precision of PWM
Lower latency on the PWM output
Support redundancy function
Smart Port enabled and support telemetry data transmission
A multifunctional receiver from FrSky! RX8R, a receiver which has 8/16ch full duplex telemetry and redundancy functions!
Parallel two RX8R to become a 16 channel receiver
Smart Port enabled, realizing two-way full duplex transmission
Supports redundant transmission of two Tx modules in parallel (Sbus input: the signal from the slave receiver(Sbus receiver) for backup)
The redundancy function For the master and slave receivers, when the master receiver goes into failsafe, the output signal from the slave receiver will be used until the master receiver works again. Notes
When both the master and slave receivers go into failsafe, the failsafe signal from the master receiver will be output.
The slave receiver should be in no telemetry mode
Specification:
Dimension: 46.25×26.6×14.2mm (L×W×H)
Weight: 12.1g
Number of Channels: 16CH (1-8ch from conventional channel output, 1-16ch from SBUS port, or combine two RX8R to become a 16 channels receivers)
With RSSI Output on Board: Analog 0-3.3V
Operating Voltage Range: 4.0-10V
Operating Current: 100mA@5V
Operating Range: full range (>1.5km)
Firmware Upgradeable
Compatibility: FrSky radios/transmitter modules in D8/D16 mode
Please note this rx has the FrSky EU LBT firmware installed, which greatly improves RF performance, range and stability. This firmware is not compatible with the previous EU firmware. It is recommended that you upgrade your radios, modules and receivers from the old EU firmware to the corresponding EU LBT firmware. Use either FrSky radios or PC for upgrading. Please refer to the FrSky website download section for the firmware download.
Includes:
RX8R Receiver
Manual
FrSky Downloads for Latest Firmware, Manuals and Certificates Product Manual