Hitec D956WP Metal Gear Servo
Code: HT-01-01-D956WP-Metal-Gear-Servo
The HiTEC D956WP is based on the D954SW servo this IP-67 rated version is a true waterproof and dust resistant upgrade that’s just perfect for 1/10-scale rock crawlers, off-road trucks, boats and even seaplanes. As with Hitec’s entire ‘D’ series, this technologically-advanced servo is powered by a 32-bit MCU (Micro Control Unit) and 12-bit ADC (Analog to Digital Converter). Beautifully engineered with rapid, high resolution response the D954SW has unprecedented programmability and a wide voltage capability, allowing it to deliver leading-edge performance for all your radio control needs. It’s tough too. With incredibly durable steel gears, dual ball bearings and a hardened steel output shaft, the high-end performing D956WP offers mighty torque and the reliability to keep you flying, driving and sailing in the most hostile of environments.
Features:
32-bit MCU with 12-bit ADC circuitry
4096 resolution
Programmable PWM digital amplifier
Wide operating voltage (4.8 - 7.4 volts DC)
Long life potentiometer (1M cycles)
Dual ball raced output shaft
Coreless metal brush motors
Nylon reinforced plastic upper and lower case
Diamond cut aluminium centre case heat-sink
25 tooth output spline
Waterproof case
End Point programming
Direction programming
Fail-safe programming
Dead band programming
Speed reduction programming
Soft start programming
Overload protection programming
Specification:
Performance Specification
Operating Voltage Range (Volts DC) - 4.8V ~ 7.4V
Speed (Second @ 60°) - 0.19 ~ 0.12
Maximum Torque Range oz. / in. - 251 ~ 405
Maximum Torque Range kg. / cm. - 18.0 ~ 29.0
Current Draw at Idle - 30 mA
No Load Operating Current Draw - 500 mA
Stall Current Draw - 5,200 mA
Dead Band Width - 1 µs
Physical Specification
Dimensions (Inches) - 1.57 x 0.78 x 1.46
Dimensions (Metric) - 40.0 x 20.0 x 37.0
Weight (Ounces) - 2.40
Weight (Gram) - 68.0
Circuit Type - 32bit Programable Digital
Motor Type - Coreless Metal Brush
Gear Material - MK 1st Gear & 3 Steel Alloy Gears
Bearing Type - Dual Ball Bearing
Output Shaft (type / Ømm) - H25T
Case Material - Plastic / Aluminum
Dust / Water Resistance - IP67 Rating
Connector Gauge (AWG) / Strand Count - 20 / 80
Package contains:
1x D956WP Waterproof, High Torque, Metal Gear Servo
Code: HT-01-01-D956WP-Metal-Gear-Servo
The HiTEC D956WP is based on the D954SW servo this IP-67 rated version is a true waterproof and dust resistant upgrade that’s just perfect for 1/10-scale rock crawlers, off-road trucks, boats and even seaplanes. As with Hitec’s entire ‘D’ series, this technologically-advanced servo is powered by a 32-bit MCU (Micro Control Unit) and 12-bit ADC (Analog to Digital Converter). Beautifully engineered with rapid, high resolution response the D954SW has unprecedented programmability and a wide voltage capability, allowing it to deliver leading-edge performance for all your radio control needs. It’s tough too. With incredibly durable steel gears, dual ball bearings and a hardened steel output shaft, the high-end performing D956WP offers mighty torque and the reliability to keep you flying, driving and sailing in the most hostile of environments.
Features:
32-bit MCU with 12-bit ADC circuitry
4096 resolution
Programmable PWM digital amplifier
Wide operating voltage (4.8 - 7.4 volts DC)
Long life potentiometer (1M cycles)
Dual ball raced output shaft
Coreless metal brush motors
Nylon reinforced plastic upper and lower case
Diamond cut aluminium centre case heat-sink
25 tooth output spline
Waterproof case
End Point programming
Direction programming
Fail-safe programming
Dead band programming
Speed reduction programming
Soft start programming
Overload protection programming
Specification:
Performance Specification
Operating Voltage Range (Volts DC) - 4.8V ~ 7.4V
Speed (Second @ 60°) - 0.19 ~ 0.12
Maximum Torque Range oz. / in. - 251 ~ 405
Maximum Torque Range kg. / cm. - 18.0 ~ 29.0
Current Draw at Idle - 30 mA
No Load Operating Current Draw - 500 mA
Stall Current Draw - 5,200 mA
Dead Band Width - 1 µs
Physical Specification
Dimensions (Inches) - 1.57 x 0.78 x 1.46
Dimensions (Metric) - 40.0 x 20.0 x 37.0
Weight (Ounces) - 2.40
Weight (Gram) - 68.0
Circuit Type - 32bit Programable Digital
Motor Type - Coreless Metal Brush
Gear Material - MK 1st Gear & 3 Steel Alloy Gears
Bearing Type - Dual Ball Bearing
Output Shaft (type / Ømm) - H25T
Case Material - Plastic / Aluminum
Dust / Water Resistance - IP67 Rating
Connector Gauge (AWG) / Strand Count - 20 / 80
Package contains:
1x D956WP Waterproof, High Torque, Metal Gear Servo
Code: HT-01-01-D956WP-Metal-Gear-Servo
The HiTEC D956WP is based on the D954SW servo this IP-67 rated version is a true waterproof and dust resistant upgrade that’s just perfect for 1/10-scale rock crawlers, off-road trucks, boats and even seaplanes. As with Hitec’s entire ‘D’ series, this technologically-advanced servo is powered by a 32-bit MCU (Micro Control Unit) and 12-bit ADC (Analog to Digital Converter). Beautifully engineered with rapid, high resolution response the D954SW has unprecedented programmability and a wide voltage capability, allowing it to deliver leading-edge performance for all your radio control needs. It’s tough too. With incredibly durable steel gears, dual ball bearings and a hardened steel output shaft, the high-end performing D956WP offers mighty torque and the reliability to keep you flying, driving and sailing in the most hostile of environments.
Features:
32-bit MCU with 12-bit ADC circuitry
4096 resolution
Programmable PWM digital amplifier
Wide operating voltage (4.8 - 7.4 volts DC)
Long life potentiometer (1M cycles)
Dual ball raced output shaft
Coreless metal brush motors
Nylon reinforced plastic upper and lower case
Diamond cut aluminium centre case heat-sink
25 tooth output spline
Waterproof case
End Point programming
Direction programming
Fail-safe programming
Dead band programming
Speed reduction programming
Soft start programming
Overload protection programming
Specification:
Performance Specification
Operating Voltage Range (Volts DC) - 4.8V ~ 7.4V
Speed (Second @ 60°) - 0.19 ~ 0.12
Maximum Torque Range oz. / in. - 251 ~ 405
Maximum Torque Range kg. / cm. - 18.0 ~ 29.0
Current Draw at Idle - 30 mA
No Load Operating Current Draw - 500 mA
Stall Current Draw - 5,200 mA
Dead Band Width - 1 µs
Physical Specification
Dimensions (Inches) - 1.57 x 0.78 x 1.46
Dimensions (Metric) - 40.0 x 20.0 x 37.0
Weight (Ounces) - 2.40
Weight (Gram) - 68.0
Circuit Type - 32bit Programable Digital
Motor Type - Coreless Metal Brush
Gear Material - MK 1st Gear & 3 Steel Alloy Gears
Bearing Type - Dual Ball Bearing
Output Shaft (type / Ømm) - H25T
Case Material - Plastic / Aluminum
Dust / Water Resistance - IP67 Rating
Connector Gauge (AWG) / Strand Count - 20 / 80
Package contains:
1x D956WP Waterproof, High Torque, Metal Gear Servo