








Hobbywing - XRotor FPV G2 45a 4in1
Code: HBW-00-01-XRotor-FPV-G2-45a-4in1
The Hobbywing Xrotor FPV G2 4in1 ESC comes in an ultra-compact 20X20mm mounting hole spacing design, ensuring a streamlined, lightweight profile for your drone. It’s so small, it makes a hummingbird look like a jumbo jet.
Armed with a cutting edge 32-bit ARM F4 microprocessor. This runs at a breathtaking operating frequency of 120MHz, tailored specifically for competition-level FPV.
With support for a dynamic PWM frequency ranging from 24K to 128KHz, it allows you to adjust your throttle control with the accuracy of a Swiss watchmaker. Whether you’re threading the needle through an obstacle or pushing for that final burst of speed, the Hobbywing Xrotor FPV G2 4in1 ESC delivers pinpoint accuracy every time.
Packaged in a package the size of a flight controller (FC), this ESC includes four high-performance 45A BLHeli_32 DShot1200 ESCs and a built-in voltmeter. Your FC can monitor amp and volt in real time.
Moreover, with two ways for connecting the ESC to an FC, either by soft cables or soldering via solder tabs and a shock-absorbing design of mounting holes, this device is as flexible and resilient.
Features:
Lightweight and compact 20X20mm design
32-bit ARM F4 microprocessor for stellar performance
Dynamic 128KHz PWM for precise throttle control
Highly integrated with 4 high-performance 45A BLHeli_32 DShot1200 ESCs
Built-in voltmeter for real-time amp and volt monitoring
Two connection methods for ESC to FC – soft cables and solder tabs
Shock-absorbing mounting holes design
Tailored for competition-level FPV racing
Specification:
Product number - 30902065
Cont./Peak Current - 45Ax4/60Ax4
Input Voltage - 3-6s Lipo
BEC Output - No
Input Wires - Red-14AWG-100mm x1
Output Wires - Black-14AWG-100mm x1
Input Connectors - XT60 (w/ Wires Soldered on)
Output Connectors - No
Size - 40x33x5mm
Weight - 12g
Firmware - Hobbywing_XRotor_BLHeli_32_AT421
ESC Programming - Supported
Programming Tool - BLHeliSuite32
DEO - Supported
Throttle Range Calibration - Supported
Oneshot125 Mode - Supported
Oneshot42 Mode - Supported
Multishot Mode - Supported
DShot150/300/600/1200 - Supported
Timing - Supported
Motor Rotation - Supported
Package contains:
1x XRotor 45a 4in1 FPV G2
Code: HBW-00-01-XRotor-FPV-G2-45a-4in1
The Hobbywing Xrotor FPV G2 4in1 ESC comes in an ultra-compact 20X20mm mounting hole spacing design, ensuring a streamlined, lightweight profile for your drone. It’s so small, it makes a hummingbird look like a jumbo jet.
Armed with a cutting edge 32-bit ARM F4 microprocessor. This runs at a breathtaking operating frequency of 120MHz, tailored specifically for competition-level FPV.
With support for a dynamic PWM frequency ranging from 24K to 128KHz, it allows you to adjust your throttle control with the accuracy of a Swiss watchmaker. Whether you’re threading the needle through an obstacle or pushing for that final burst of speed, the Hobbywing Xrotor FPV G2 4in1 ESC delivers pinpoint accuracy every time.
Packaged in a package the size of a flight controller (FC), this ESC includes four high-performance 45A BLHeli_32 DShot1200 ESCs and a built-in voltmeter. Your FC can monitor amp and volt in real time.
Moreover, with two ways for connecting the ESC to an FC, either by soft cables or soldering via solder tabs and a shock-absorbing design of mounting holes, this device is as flexible and resilient.
Features:
Lightweight and compact 20X20mm design
32-bit ARM F4 microprocessor for stellar performance
Dynamic 128KHz PWM for precise throttle control
Highly integrated with 4 high-performance 45A BLHeli_32 DShot1200 ESCs
Built-in voltmeter for real-time amp and volt monitoring
Two connection methods for ESC to FC – soft cables and solder tabs
Shock-absorbing mounting holes design
Tailored for competition-level FPV racing
Specification:
Product number - 30902065
Cont./Peak Current - 45Ax4/60Ax4
Input Voltage - 3-6s Lipo
BEC Output - No
Input Wires - Red-14AWG-100mm x1
Output Wires - Black-14AWG-100mm x1
Input Connectors - XT60 (w/ Wires Soldered on)
Output Connectors - No
Size - 40x33x5mm
Weight - 12g
Firmware - Hobbywing_XRotor_BLHeli_32_AT421
ESC Programming - Supported
Programming Tool - BLHeliSuite32
DEO - Supported
Throttle Range Calibration - Supported
Oneshot125 Mode - Supported
Oneshot42 Mode - Supported
Multishot Mode - Supported
DShot150/300/600/1200 - Supported
Timing - Supported
Motor Rotation - Supported
Package contains:
1x XRotor 45a 4in1 FPV G2
Code: HBW-00-01-XRotor-FPV-G2-45a-4in1
The Hobbywing Xrotor FPV G2 4in1 ESC comes in an ultra-compact 20X20mm mounting hole spacing design, ensuring a streamlined, lightweight profile for your drone. It’s so small, it makes a hummingbird look like a jumbo jet.
Armed with a cutting edge 32-bit ARM F4 microprocessor. This runs at a breathtaking operating frequency of 120MHz, tailored specifically for competition-level FPV.
With support for a dynamic PWM frequency ranging from 24K to 128KHz, it allows you to adjust your throttle control with the accuracy of a Swiss watchmaker. Whether you’re threading the needle through an obstacle or pushing for that final burst of speed, the Hobbywing Xrotor FPV G2 4in1 ESC delivers pinpoint accuracy every time.
Packaged in a package the size of a flight controller (FC), this ESC includes four high-performance 45A BLHeli_32 DShot1200 ESCs and a built-in voltmeter. Your FC can monitor amp and volt in real time.
Moreover, with two ways for connecting the ESC to an FC, either by soft cables or soldering via solder tabs and a shock-absorbing design of mounting holes, this device is as flexible and resilient.
Features:
Lightweight and compact 20X20mm design
32-bit ARM F4 microprocessor for stellar performance
Dynamic 128KHz PWM for precise throttle control
Highly integrated with 4 high-performance 45A BLHeli_32 DShot1200 ESCs
Built-in voltmeter for real-time amp and volt monitoring
Two connection methods for ESC to FC – soft cables and solder tabs
Shock-absorbing mounting holes design
Tailored for competition-level FPV racing
Specification:
Product number - 30902065
Cont./Peak Current - 45Ax4/60Ax4
Input Voltage - 3-6s Lipo
BEC Output - No
Input Wires - Red-14AWG-100mm x1
Output Wires - Black-14AWG-100mm x1
Input Connectors - XT60 (w/ Wires Soldered on)
Output Connectors - No
Size - 40x33x5mm
Weight - 12g
Firmware - Hobbywing_XRotor_BLHeli_32_AT421
ESC Programming - Supported
Programming Tool - BLHeliSuite32
DEO - Supported
Throttle Range Calibration - Supported
Oneshot125 Mode - Supported
Oneshot42 Mode - Supported
Multishot Mode - Supported
DShot150/300/600/1200 - Supported
Timing - Supported
Motor Rotation - Supported
Package contains:
1x XRotor 45a 4in1 FPV G2